Kubota G23 Workshop Manual Download Page 66 | Manualshive

Page: 66 / 343

Kubota G23 Workshop Manual Download Page 66

GENERAL

G23, G26, WSM

G-48

(EU)

(Continued)

Q

Anti-Freeze

CAUTION

To avoid personal injury :

• When using anti-freeze, put on some protection such as

rubber gloves (Anti-freeze contains poison.).

• If anti-freeze is ingested, induce vomiting at once and seek

medical attention.

• When anti-freeze comes in contact with the skin or

clothing, wash it off immediately.

• Do not mix different types of Anti-freeze. The mixture can

produce chemical reaction causing harmful substances.

• Anti-freeze is extremely flammable and explosive under

certain conditions. Keep fire and children away from
anti-freeze.

• When draining fluids from the engine, place some

container underneath the engine body.

• Do not pour waste onto the grounds, down a drain, or into

any water source.

• Also, observe the relevant environmental protection

regulations when disposing of anti-freeze.

If it freezes, coolant can damage the cylinders and radiator. If

the ambient temperature falls below 0 °C (32 °F) or before a
long-term storage, let out cooling water completely, or mix fresh
water with long-life coolant and fill the radiator and reserve tank with
the mixture.
1. Long-life coolant (hereafter LLC) comes in several types. Use

ethylene glycol (EG) type for this engine.

2. Before employing LLC-mixed cooling water, fill the radiator with

fresh water and empty it again. repeat this procedure 2 or 3
times to clean up the inside.

3. Mixing the LLC

Put the LLC in cooling water in the percentage (%) for a target
temperature. When mixing, stir it up well, and then fill into the
radiator.

4. The procedure for mixing of water and anti-freeze differs

according to the make of the anti-freeze and the ambient
temperature. Refer to SAE J1034 standard, more specially also
to SAE J814c.

IMPORTANT

• When the anti-freeze is mixed with water, the anti-freeze

mixing ratio must be less than 50 %.

* At 1.013 x 10

5

Pa (760 mmHg) pressure (atmospheric). A

higher boiling point is obtained by using a radiator pressure cap
which permits the development of pressure within the cooling
system.

(To be continued)

Vol %

Anti-freeze

Freezing Point

Boiling Point*

°C

°F

°C

°F

40

–24

–12

106

222

50

–37

–34

108

226

KiSC issued 08, 2009 A

«
...
64
65
66
67
68
...
»

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands