manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 277

ELECTRICAL SYSTEM

G23, G26, WSM

6-M10

(EU)

6. BUZZER SYSTEM

[1] ELECTRICAL CIRCUIT

Buzzer system consists of the battery (5), the slow

blow fuse (2), the main switch (4), the PTO shift lever
switch 1 (3), the buzzer (7), the grass collector duct
switch (6) and etc..

9Y1210294ELM0010US0

[2] BUZZER

As shown in the electrical circuit, when the grass

collector is full of grass, the grass collector duct switch is
set to 

"ON"

.

At this moment the buzzer alerts the noise.
When the grass collector is not full of grass, the

grass duct switch is set to 

"OFF"

.

At this condition, the buzzer does not alert the noise.

9Y1210294ELM0011US0

[3] GRASS COLLECTOR DUCT SWITCH

Grass collector duct switch is located at the grass

collector duct.

The grass collector duct switch detects the grass

quantity in the grass collector bag.

When the grass bag is full of grass, the switch lever

(3) is set to 

"ON"

.

At this moment, the battery current from the buzzer

flows through the grass collector duct switch to the
machine frame earth.

When the grass bag is not full of grass, the switch

lever (3) is not set to 

"ON"

.

9Y1210294ELM0012US0

(1) Fuse (10A)
(2) Slow Blow Fuse (50A)
(3) PTO Shift Lever Switch 1
(4) Main Switch

(5) Battery
(6) Grass Collector Duct Switch
(7) Buzzer

(1) Terminal (Black)
(2) Terminal (Red)
(3) Lead (Red)

(4) Buzzer Body
(5) Lead (Black)

(1) Terminal 

1

(2) Lead (COM) 

(Connected to Frame Earth)

(3) Switch Lever

(4) Terminal 

2

(5) Lead (NC) 

(Connected to Buzzer)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands