manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 122

ENGINE

G23, G26, WSM

1-S40

(EU)

(6) Flywheel and Crankshaft

Flywheel

1. Secure the flywheel to keep it from turning using a flywheel

stopper.

2. Remove all flywheel screws (1) and then remove the flywheel

(2).

(When reassembling)

• Align the 

"1TC"

 mark 

(a)

 on the outer surface of the flywheel

horizontally with the alignment mark 

(b)

 on the rear end plate.

Now fit the flywheel i position.

• Apply engine oil to the threads and the undercut surface of the

flywheel screw and fit the screw.

9Y1210294ENS0047US0

Bearing Case Cover

1. Remove the bearing case cover mounting screws.
2. Remove the bearing case cover (6).

(When reassembling)

• Fit the bearing case gasket (3) and the bearing case cover

gasket (4) with correct directions.

• Install the bearing case cover (6) to position the casting mark

"UP"

 on it upward.

• Apply engine oil to the oil seal (5) lip and take care that it is not

rolled when installing.

• Tighten the bearing case cover mounting screws with even

force on the diagonal line.

9Y1210294ENS0048US0

Tightening torque

Flywheel screw

54 to 58 N·m
5.5 to 6.0 kgf·m
40 to 43 lbf·ft

(1) Flywheel Screw
(2) Flywheel

(a) 1TC Mark
(b) Alignment Plate

Tightening torque

Bearing case cover 
mounting screw

9.81 to 11.2 N·m
1.00 to 1.15 kgf·m
7.24 to 8.31 lbf·ft

(1) Bearing Case Cover Mounting 

Screw (Inside)

(2) Bearing Case Cover Mounting 

Screw (Outside)

(3) Bearing Case Gasket
(4) Bearing Case Cover Gasket

(5) Oil Seal
(6) Bearing Case Cover

(a) Top Mark "UP"
(b) Upside

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands