manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 184

TRANSAXLE

G23, G26, WSM

2-S23

(EU)

Separating Transmission Assembly

1. Remove the wiring harness (1) from the transmission case

assembly (8).

2. Disconnect the hydraulic pipe (2) from the transmission case

assembly (8).

3. Disconnect the HST damper (3) and the brake rod (7).
4. Remove the transmission assembly mounting bolts.
5. Hook the transmission assembly with nylon slings.

Loose the parking lock over the rear coupling (5).

[G26 only]
Remove the PTO return pipe from the transmission case
assembly (8).

6. Remove the transmission case assembly (8) from the machine

frames.

(When reassembling)

9Y1210294TXS0025US0

Tightening torque

Transmission assembly 
mounting bolt (M14)

135.9 to 147 N·m
13.9 to 15.0 kgf·m
100.2 to 108.4 lbf·ft

(1) Wiring Harness
(2) Hydraulic Pipe
(3) HST Damper
(4) Speed Change Rod

(5) Rear Coupling
(6) Return Spring
(7) Brake Rod
(8) Transmission Case Assembly

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands