manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 49

GENERAL

G23, G26, WSM

G-31

(EU)

Greasing 8

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

greasing.

1. Apply a grease to the following positions as figures.

9Y1210294GEG0032US0

Checking Gear Box Oil Level

 CAUTION

To avoid personal injury :

• Always stop the engine and remove the key before

checking oil.

1. Park the machine on a flat surface and lower the mower to the

ground.
To check the oil level, draw out the dipstick, wipe it clean,
replace it, and draw it out again. Check to see that the oil level
lies between the two notches.
If the level is too low, add new oil to the prescribed level at the
oil inlet.
(Refer to "LUBRICANTS, FUEL AND COOLANT" in this
section.)

NOTE

• Check the oil level of the transmission case with the mower

lifted up.

IMPORTANT

• If oil level is low, do not run the engine.

9Y1210294GEG0033US0

(1) Dump Flap (HD)
(2) Seat Pivot

(3) Seat Adjuster

(1) Oil level Dipstick

A : Oil level is acceptable within this 

range

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands