Kubota G23 Workshop Manual Download Page 170

Page: 170 / 343

TRANSAXLE

G23, G26, WSM

2-S9

(EU)

High Relief Pressure (Forward)

CAUTION

• When checking, park the machine on flat ground.

1. Lift up the rear wheels by supporting the machine frame.
2. Remove the hexagon socket head plug (G 1/4) from

(4), then

install the adaptor, cable and pressure gauge.

3. Start the engine and run it at the maximum speed.
4. Depress the speed control pedal to

"Forward"

, engage the

brake carefully as shown in the figure. Read the pressure gauge
to measure the high relief pressure.

5. If the measurement is not same as factory specification, check

the high pressure relief valve and related hydraulic components.

IMPORTANT

• Measure quickly the high relief pressure within about 10

seconds

NOTE

• When reinstalling the hexagon socket head plug, apply

liquid lock (Three Bond 1324 or its equivalent) to the plug.

9Y1210294TXS0008US0

High relief pressure
(Forward)

Factory specification
(Oil temperature at
50 °C, 122 °F)

24.0 to 25.0 MPa
245 to 255 kgf/cm

3480 to 3620 psi

Tightening torque

Hexagon socket head plug
(

and

port)

30 to 44 N·m
3.0 to 4.5 kgf·m
22 to 32 lbf·ft

(1) Brake Lever
(2)

Port (Reverse)

(3) By-pass Valve
(4)

Port (Forward)

(5) Adaptor (Forward Port)
(6) Brake Lever Holding Rod

A : Braking

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands