manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 106

ENGINE

G23, G26, WSM

1-S24

(EU)

Battery Cables and Battery

 CAUTION

• When disconnecting the battery cables, disconnect the

negative cable from the battery first. When connecting,
connect the positive cable to the battery first.

1. Remove the under panel.
2. Disconnect the negative cable (2) from the battery (1).
3. Disconnect the positive cable (3) from the battery (1) and

remove the battery (1).

9Y1210294ENS0019US0

Removing Front Weight

1. Loosen the front weight mounting bolts (2).
2. Remove the front weight (3).
3. Remove the front weight bracket (1).
4. Remove the hydraulic hose cover (4).

9Y1210294ENS0020US0

Bonnet and Under Cover

1. Open the bonnet (3) and then loosen the knob bolts and pull

forward to remove the under cover (4).

2. Disconnect the connectors (1) for head light and remove the

bonnet bracket (2) with bonnet.

9Y1210294ENS0021US0

(1) Battery
(2) Negative Cable

(3) Positive Cable

(1) Front Weight
(2) Front Weight Bolt

(3) Front Weight
(4) Hydraulic Hose Cover

(1) Connector
(2) Bonnet Bracket

(3) Bonnet
(4) Under Cover

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands