manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 252

HYDRAULIC SYSTEM

G23, G26, WSM

5-S6

(EU)

Checking Pump Delivery Oil to Power Steering (EF)

IMPORTANT

• Use the instruction with the flowmeter when you use the

flowmeter.

• While testing, do not close the flowmeter loading valve

completely.

1. Disconnect the power steering (IN) hose (1) from the power

steering (IN) tube (3).

2. Fix the adaptor, the hydraulic flowmeter hose and the hydraulic

flowmeter to the power steering (IN) tube (3).

3. Remove the transmission fluid filling plug, and fix the flowmeter

hose and the flowmeter.

4. Check that a flow volume meets the specifications when the

engine revolution is at about 3200 min

-1

 (rpm).

5. If the volume varies from the specification, replace the priority

valve, then take measurement again.

Condition

• Engine speed

3200 min

-1

 (rpm)

• Oil temperature

50 °C (122 °F)

9Y1210294HYS0005US0

Power steering oil flow

Factory specification

Above
9.5 L/min
2.5 U.S.gals/min
2.1 Imp.gals/min

(1) Power Steering (IN) Hose
(2) Power Steering Controller
(3) Power Steering (IN) Tube
(4) Flow Priority Valve
(5) Adaptor

(6) Flowmeter Hose (IN)
(7) Flowmeter
(8) Flowmeter Hose (OUT)
(9) Transmission Case

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands