manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 302

ELECTRICAL SYSTEM

G23, G26, WSM

6-S24

(EU)

Engine Oil Pressure Switch Continuity

1. Disconnect the lead (2) from the engine oil pressure switch (1).
2. Measure the resistance with an ohmmeter across the switch

terminal and the chassis.

3. If 0 

Ω

 is not indicated in the normal state, the switch is faulty.

4. If infinity is not indicated at pressure over 4.9 kPa

(0.050 kgf/cm

2

, 0.71 psi), the switch is faulty.

9Y1210294ELS0027US0

(15) Gauge

Fuel Level Sensor

1) Sensor Continuity

1. Remove the fuel level sensor from the fuel tank.
2. Measure the resistance with an ohmmeter across the sensor

terminal and its body.

3. If the reference values are not indicated, the sensor is faulty.

9Y1210294ELS0028US0

Coolant Temperature Sensor (Thermo Unit)

1) Lead Terminal Voltage

1. Disconnect the lead from the coolant temperature sensor after

turning the main switch 

OFF

.

2. Turn the main switch 

ON

 and measure the voltage with a

voltmeter across the lead terminal and the chassis.
If the voltage differs from the battery voltage, the wiring harness,
fuse or coolant temperature gauge is faulty.

2) Sensor Continuity

1. Measure the resistances with an ohmmeter across the sensor

terminal and the chassis.

2. If the reference value is not indicated, the sensor is faulty.

9Y1210294ELS0029US0

Resistance (Switch 
terminal – Chassis)

In normal state

0 

Ω

At pressure over approx. 
4.9 kPa (0.050 kgf/cm

2

, 

0.71 psi)

Infinity

(1) Engine Oil Pressure Switch

(2) Lead

Resistance 
(Sensor terminal - 
its body)

Reference 
value

Float at upper 
-most position

1 to 5 

Ω

Float at lower 
-most position

103 to 117 

Ω

E : Empty

F : Full

Voltage

Lead terminal – Chassis

Approx. battery voltage

Resistance 
(Sensor terminal 
– Chassis)

Reference 
valve

Approx. 16.1 

Ω

 at 120 °C (248 °F)

Approx. 27.4 

Ω

 at 100 °C (212 °F)

Approx. 51.9 

Ω

 at 80 °C (176 °F)

Approx. 153.9 

Ω

 at 50 °C (122 °F)

(1) Coolant Temperature Sensor

(a) From Temperature Gauge

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands