manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 142

ENGINE

G23, G26, WSM

1-S60

(EU)

Oil Clearance between Crankshaft Journal and Crankshaft
Bearing 1 (G23)

1. Measure the O.D. of the crankshaft front journal with an outside

micrometer.

2. Measure the I.D. of the crankshaft bearing 1 with an inside

micrometer, and calculate the oil clearance.

3. If the oil clearance exceeds the allowable limit, replace the

crankshaft bearing 1.

4. If the same size bearing is useless because of the crankshaft

journal wear, replace it with an undersize one referring to the
table and the figure.

(Reference)

• Undersize crankshaft bearing 1

• Undersize dimensions of crankshaft journal

9Y1210294ENS0079US0

Oil Clearance between 
crankshaft journal and 
crankshaft bearing 1

Factory specification

0.0340 to 0.106 mm
0.00134 to 0.00417 in.

Allowable limit

0.20 mm
0.0079 in.

Crankshaft journal O.D.

Factory specification

43.934 to 43.950 mm
1.7297 to 1.7303 in.

Crankshaft bearing 1 I.D.

Factory specification

43.984 to 44.040 mm
1.7317 to 1.7338 in.

Undersize

Bearing

Code Number

Marking

0.20 mm
0.0079 in.

Crankshaft bearing 1 02

1G460-23910

020 US

0.40 mm
0.016 in.

Crankshaft bearing 1 04

1G460-23920

040 US

Undersize

Models

0.20 mm

0.0079 in.

0.40 mm
0.016 in.

Dimension 

A

All 

models

1.8 to 2.2 mm radius

0.071 to 0.086 in. radius

1.8 to 2.2 mm radius

0.071 to 0.086 in. radius

*Dimension 

B

All 

models

1.0 to 1.5 mm relief

0.040 to 0.059 in. relief

1.0 to 1.5 mm relief

0.040 to 0.059 in. relief

Dimension 

C

43.734 to 43.750 mm 

dia.

1.7219 to 1.7224 in. dia.

43.534 to 43.550 mm 

dia.

1.7140 to 1.7145 in. dia.

The crankshaft journal must be fine-finished to higher than Rmax=0.8S
*Holes to be de-burred and edges rounded with 1.0 to 1.5 mm (0.040 to 
0.059 in.) relief.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands