Kubota G23 Workshop Manual Download Page 97

Page: 97 / 343

ENGINE

G23, G26, WSM

1-S15

(EU)

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

(1) Engine Body

Compression Pressure

1. Run the engine until it is warmed up.
2. Stop the engine.
3. Remove the air cleaner, the muffler and all glow plugs (or

nozzles).

4. Set a compression tester with the adaptor to the glow plug hole

(or nozzle hole).
Nozzle hole : Adaptor

(07909-31231)

Glow plug hole : Adaptor

(07909-31301)

5. Disconnect the connector of engine stop solenoid and keep the

engine stop position (non-injection). Then, run the engine with
the starter and measure the compression pressure.

6. Repeat steps 4 and 5 for each cylinder.
7. If the measurement is below the allowable limit, apply a small

amount of oil to the cylinder wall through the glow plug hole (or
nozzle hole) and measure the compression pressure again.

8. If the compression pressure is still less than the allowable limit,

check the top clearance, valve clearance and cylinder head.

9. If the compression pressure increases after applying oil, check

the cylinder wall and piston rings.

NOTE

• Check the compression pressure with the specified valve

clearance.

• Always use a fully charged battery for preforming this test.
• Variances in cylinder compression values should be under

10 %.

[G23]

[G26]

9Y1210294ENS0005US0

Compression pressure

Factory specification

3.53 to 4.02 MPa
36.0 to 41.0 kgf/cm

512 to 583 psi

Allowable limit

2.55 MPa
26.0 kgf/cm

370 psi

Compression pressure

Factory specification

3.73 to 4.11 MPa
38.0 to 42.0 kgf/cm

541 to 596 psi

Allowable limit

2.26 MPa
23.0 kgf/cm

328 psi

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands