manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 317

MOWER

G23, G26, WSM

7-S4

(EU)

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Checking Mower Blade

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key.
• Blades may be sharp. When you handle blades, wear heavy

gloves or wrap end of blade with a rag.

Q

Checking

The blade cutting edges should be kept sharp at all times.

Sharpen the cutting edges, if they resemble blade 

(b)

. Replace the

blades if they appear similar to blade 

(c)

.

9Y1210294MOS0004US0

Mower Deck Front to Rear Height Adjustment

 CAUTION

To avoid personal injury :

• Shut off the engine and remove the key.
• Set the parking brake.
• Allow the blades to stop before making adjustments.
• Wear heavy gloves or wrap end of the blade with a rag when

you handle blades; Blades may be sharp.

1. Park the machine on a level surface.
2. Tyre inflation pressure must be correct.
3. Raise the mower lift lever to the top position.

Turn the cutting height control dial to adjust height to the desired
height.

4. Lower the mower deck by pushing the mower lift lever forward.
5. Turn the left blade so that it is parallel to the machine direction.
6. Make sure the mower blades are level. Then tighten the lock

nuts securely.
Adjust bolts with the lock nut so that A is 0 to 5 mm 
(0 to 0.20 in.).
A = (Y) - (X)

9Y1210294MOS0005US0

(a) New Blade
(b) Worn Blade

(c) Cracked Blade

Mower deck front to rear 
height (Rear height 
minus front height)

Factory specification

0 to 5 mm
0 to 0.20 in.

(1) Lock Nut
(2) Adjusting Nut

X : Blade Front End Height
Y : Blade Rear End Height

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands