manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 253

HYDRAULIC SYSTEM

G23, G26, WSM

5-S7

(EU)

Checking Pump Delivery Oil to Control Valve

IMPORTANT

• Use the instruction with the flowmeter when you use the

flowmeter.

• While testing, do not close the flowmeter loading valve

completely.

1. Disconnect the hydraulic delivery hose (1) from the connector

(K2581-3665-0) (2) on the front case (3).

2. Fix the adaptor (5), the hydraulic flowmeter hose (IN) (6) and the

hydraulic flowmeter (7) to the connector (K2581-3665-0).

3. Remove the transmission fluid filling plug from the transmission

case (9).

4. Fix the flowmeter hose (OUT) to the transmission case (9).
5. Check that a flow volume meets the specifications when the

engine revolution is set at 3200 min

-1

 (rpm).

6. If the oil flow volume varies from the specification, replace the

flow priority valve, then take measurement again.

Condition

• Engine speed

3200 min

-1

 (rpm)

• Oil temperature

50 °C (122 °F)

9Y1210294HYS0006US0

Hydraulic pump delivery 
at no pressure

Factory specification

Above
18.0 L/min
4.8 U.S.gals/min
4.0 Imp.gals/min

(1) Delivery Hose
(2) Connector (K2581-3665-0)
(3) Front Case
(4) Flow Priority Valve
(5) Adaptor

(6) Flowmeter Hose (IN)
(7) Flowmeter
(8) Flowmeter Hose (OUT)
(9) Transmission Case

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands