manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 112

ENGINE

G23, G26, WSM

1-S30

(EU)

(2) Removing Engine Outer Parts

Draining Coolant and Removing Engine Outer Parts

 CAUTION

• Never open the radiator cap while operating or immediately

after stopping. Otherwise, hot water will spout out from the
radiator. Wait for more than ten minutes to cool the
radiator, before opening the cap.

1. Set the engine stands (2) to the crankcase.
2. Open the radiator drain plug, and remove radiator cap to

completely drain the coolant.

3. After all coolant is drained, close the drain plug.
4. Loosen the inlet hose band and the radiator hose bands, and

remove the radiator (4) with the radiator hoses (12) and the air
cleaner (5).

5. Loosen the fan belt. Remove the alternator (10), the starter

motor (8), the cooling fan (3) and the fan belt.

6. Remove the heat proof cover (9), the muffler (7) and the

exhaust manifold.

7. Remove the drive pulley from the flywheel.

9Y1210294ENS0028US0

(3) Cylinder Head and Valves

Cylinder Head Cover

1. Disconnect the breather hose.
2. Remove the cylinder head cover nuts.
3. Remove the cylinder head cover (1).

(When reassembling)

• Check to see if the cylinder head cover gasket is not defective.

9Y1210294ENS0030US0

Coolant with recovery 
tank

Capacity

G23

3.1 L
3.3 U.S.qts
2.7 lmp.qts

G26

3.3 L
3.5 U.S.qts
2.9 lmp.qts

Tightening torque

Drive pulley mounting bolt

52.8 to 55.9 N·m
5.4 to 5.7 kgf·m
38.9 to 41.2 lbf·ft

(1) Drive Pulley
(2) Engine Stand
(3) Cooling Fan
(4) Radiator Assy.
(5) Air Cleaner
(6) Inlet Hose

(7) Muffler
(8) Starter Motor
(9) Heat Proof Cover
(10) Alternator
(11) Inlet Hose
(12) Radiator Hose

Tightening torque

Cylinder head cover screw

7 to 8 N·m
0.7 to 0.9 kgf·m
5 to 6 lbf·ft

(1) Cylinder Head Cover

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands