Kubota G23 Workshop Manual Download Page 168

Page: 168 / 343

TRANSAXLE

G23, G26, WSM

2-S7

(EU)

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Adjusting Maximum Speed

Forward

1. Depress the speed control pedal (4) all the way and lengthen

the stopper bolt (2) until it touches the HST pedal stay (3).

2. Adjust the stopper bolt (2) length

"A"

to 20 mm (0.79 in.) and

lock it securely.

Reverse

1. Adjust the stopper bolt (1) length

"B"

to 18 mm (0.71 in.) and

lock it securely.

(Reference)

[G23]

[G26]

9Y1210294TXS0004US0

Preparation before HST Adjustment

CAUTION

• Park the machine on a firm and level ground.

1. Place the wooden blocks at the front and the rear side of the

wheels not to move the tractor. Remove the cover from the
fender.

2. Lift up the rear wheels safely by the rigid jacks.
3. Remove the rear right wheel from the tractor.

9Y1210294TXS0005US0

Stopper bolt length

Reference

Forward

20 mm
0.79 in.

Reverse

18 mm
0.71 in.

Maximum speed at
engine max. rpm

Reference

Forward

14.0 to 15.5 km/h
8.70 to 9.63 mph

Reverse

8.5 to 10.0 km/h
5.28 to 6.22 mph

Maximum speed at
engine max. rpm

Reference

Forward

15.5 to 17.0 km/h
9.63 to 10.57 mph

Reverse

8.5 to 10.0 km/h
5.28 to 6.22 mph

(1) Stopper Bolt (Reverse)
(2) Stopper Bolt (Forward)
(3) HST Pedal Stay
(4) Speed Control Pedal

A : Stopper Bolt Length (Forward)
B : Stopper Bolt Length (Reverse)

(1) Lock Screw
(2) HST Neutral Plate

(3) HST Neutral Spring

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands