manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 312

MOWER

G23, G26, WSM

7-M3

(EU)

3. LIFTING MECHANISM

Mower lift is performed by the mower lift cylinder (1) installed on the machine.
The mower should be kept at 

"UP"

 position when traveling.

When the mower lift lever is set to 

"UP"

 position, the mower lift cylinder (1) is extended by the oil pressure of the

hydraulic system. And the lift link (2) and the front arm (LH) (4) rotates counterclockwise.

The height link (5) and the connect link (6) are pulled.
The rear arm (LH) (7) rotates counterclockwise.
The lift lower link (LH) (8) is lifted up and the mower deck is lifted up.

9Y1210294MOM0003US0

(1) Mower Lift Cylinder
(2) Lift Link

(3) Front Arm
(4) Front Arm (LH)

(5) Height Link
(6) Connect Link

(7) Rear Arm (LH)
(8) Lift Lower Link (LH)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands