manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 126

ENGINE

G23, G26, WSM

1-S44

(EU)

Clearance between Valve Stem and Valve Guide

1. Remove carbon from the valve guide section.
2. Measure the valve stem O.D. with an outside micrometer.
3. Measure the valve guide I.D. with a small hole gauge, and

calculate the clearance.

4. If the clearance exceeds the allowable limit, replace the valves.

If it still exceeds the allowable limit, replace the valve guide.

[G23]

[G26]

9Y1210294ENS0054US0

Replacing Valve Guide

(When removing)

1. Press out the used valve guide using a valve guide replacing

tool. (Refer to "SPECIAL TOOLS".)

(When installing)

1. Clean a new valve guide and valve guide bore, and apply

engine oil to them.

2. Press in a new valve guide using a valve guide replacing tool.
3. Ream precisely the I.D. of the valve guide to the specified

dimension.

[G23]

[G26]

IMPORTANT

• Do not hit the valve guide with a hammer during

replacement.

9Y1210294ENS0055US0

Clearance between 
valve stem and valve 
guide

Factory specification

0.030 to 0.057 mm
0.0012 to 0.0022 in.

Allowable limit

0.10 mm
0.0039 in.

Valve stem O.D.

Factory specification

5.968 to 5.980 mm
0.2350 to 0.2354 in.

Valve guide I.D.

Factory specification

6.010 to 6.025 mm
0.2367 to 0.2372 in.

Clearance between 
valve stem and valve 
guide

Factory specification

0.035 to 0.065 mm
0.0014 to 0.0025 in.

Allowable limit

0.10 mm
0.0039 in.

Valve stem O.D.

Factory specification

6.960 to 6.975 mm
0.2741 to 0.2746 in.

Valve guide I.D.

Factory specification

7.010 to 7.025 mm
0.2760 to 0.2765 in.

Valve guide I.D.
(intake and exhaust)

Factory specification

6.010 to 6.025 mm
0.2367 to 0.2372 in.

Valve guide I.D.
(intake and exhaust)

Factory specification

7.010 to 7.025 mm
0.2760 to 0.2765 in.

(A) When Removing

(B) When Installing

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands