manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 305

ELECTRICAL SYSTEM

G23, G26, WSM

6-S27

(EU)

Commutator and Mica

1. Check the contact face of the commutator for wear, and grind

the commutator with emery paper if it is slightly worn.

2. Measure the commutator O.D. with an outside micrometer at

several points.

3. If the minimum O.D. is less than the allowable limit, replace the

armature.

4. If the difference of the O.D.'s exceeds the allowable limit, correct

the commutator on a lathe to the factory specification.

5. Measure the mica undercut.
6. If the undercut is less than the allowable limit, correct it with a

saw blade and chamfer the segment edges.

WSM000001ELS0034US0

Brush Wear

1. If the contact face of the brush is dirty or dusty, clean it with

emery paper.

2. Measure the brush length 

(A)

 with vernier calipers.

3. If the length is less than the allowable limit, replace the yoke

assembly and brush holder.

9Y1210294ELS0034US0

Brush Holder

1. Check the continuity across the brush holder and the holder

support with an ohmmeter.

2. If it conducts, replace the brush holder.

9Y1210294ELS0035US0

Commutator O.D.

Factory specification

30.0 mm
1.181 in.

Allowable limit

29.0 mm
1.142 in.

Difference of O.D.'s

Factory specification

Less than
0.02 mm
0.0008 in.

Allowable limit

0.05 mm 
0.0020 in.

Mica undercut

Factory specification

0.50 to 0.80 mm
0.020 to 0.031 in.

Allowable limit

0.2 mm
0.008 in.

(1) Segment
(2) Undercut
(3) Mica

(a) Correct
(b) Incorrect

Brush length 

(A)

Factory specification

14.0 mm
0.551 in.

Allowable limit

9.0 mm
0.354 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands