manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 157

TRANSAXLE

G23, G26, WSM

2-M7

(EU)

(3) PTO Clutch "Disengaged"

When the PTO lever is set to 

"DISENGAGED"

 position, the PTO clutch wire (7) is free.

Since the spring (2) pulls the tension PTO arm (3), the tension PTO pulley (14) is separated from the V belt (11).
The V belt is free and rotation of the pulley (1) is not transmitted to the pulley (9).
Since the spring (8) pulls the PTO brake assy. (12), the brake shoe (10) mounted on the PTO brake assy. (12)

brakes the rotation of the pulley (9).

9Y1210294TXM0010US0

(1) Pulley (Engine Flywheel Side)
(2) Spring
(3) Tension PTO Arm
(4) Stay

(5) Spring
(6) PTO Wire Bracket
(7) Clutch Wire
(8) Spring

(9) Pulley (PTO Clutch Side)
(10) Brake Shoe
(11) V Belt

(12) PTO Brake Assy.
(13) Release Arm
(14) Tension PTO Pulley

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands