manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 24

GENERAL

G23, G26, WSM

G-6

(EU)

[2] BATTERY

• Take care not to confuse positive and negative terminal posts.
• When removing battery cables, disconnect negative cable first.

When installing battery cables, check for polarity and connect
positive cable first.

• Do not install any battery with capacity other than is specified

(Ah).

• After connecting cables to battery terminal posts, apply high

temperature grease to them and securely install terminal covers
on them.

• Do not allow dirt and dust to collect on battery.

 CAUTION

• Take care not to let battery liquid spill on your skin and

clothes. If contaminated, wash it off with water
immediately.

• Before recharging the battery, remove it from the machine.
• Before recharging, remove cell caps.
• Do recharging in a well-ventilated place where there is no

open flame nearby, as hydrogen gas and oxygen are
formed.

WSM000001GEG0071US1

[3] FUSE

• Use fuses with specified capacity.

Neither too large or small capacity fuse is acceptable.

• Never use steel or copper wire in place of fuse.
• Do not install working light, radio set, etc. on machine which is

not provided with reserve power supply.

• Do not install accessories if fuse capacity of reserve power

supply is exceeded.

WSM000001GEG0072US1

[4] CONNECTOR

• For connector with lock, push lock to separate.

WSM000001GEG0073US1

• In separating connectors, do not pull wire harnesses.
• Hold connector bodies to separate.

WSM000001GEG0074US1

(1) Fuse
(2) Fusible Link

(3) Slow Blow Fuse

(A) Push

(A) Correct

(B) Incorrect

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands