manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 172

TRANSAXLE

G23, G26, WSM

2-S11

(EU)

Checking and Adjusting HST Neutral Spring (for Dynamic
Braking)

 WARNING

• Do not operate if machine moves on level ground with foot

off speed control pedal.

• If machine moves on level ground with foot off the pedal,

or, if the pedal is too slow in returning to "Neutral" position
when removing the foot from the pedal, adjust the HST
neutral spring.

The HST neutral spring located under the front right side of the

fender can adjust returning spring of speed control pedal.

Since the HST neutral spring tension is weakened, the HST

tension should be checked and adjusted every 100 hours.
1. Checking the HST neutral spring tension : Dynamic braking

• Start the engine and hold the maximum engine speeds.
• Operate the machine on the concrete level ground.
• Depress the speed control pedal to 

"Forward"

.

• Release the foot from the speed control pedal.
• Check the distance between the foot releasing point and the

machine stopping point.

• If the distance is more than approximately 3 to 5 m (10 to

16 feet), strengthen the HST neutral spring tension so that
the machine will stop in approximately 3 to 5 m (10 to 16
feet) after releasing the foot from the speed control pedal.

(Reference)

2. Remove the step from the machine.

• Loosen the lock nut (1).
• Turn the adjusting nut (2) half turn to pull the HST neutral

spring (3).

• Tighten and lock the lock nut (1).
• Start the engine and check dynamic brake as mentioned

former.

• If the machine will not stop with dynamic brake in

approximately 3 to 5 m (10 to 16 feet), adjust the neutral
spring again.

9Y1210294TXS0009US0

Distance 

"L"

 between 

the foot releasing point 
and the machine 
stopping point

Reference

Approximately
3 to 5 m (10 to 16 feet)

Length 

"A"

 of adjusting 

rod at shipping the 
machine from the factory

Reference

20 mm (0.79 in.)

(1) Lock Nut
(2) Adjusting Nut
(3) HST Neutral Spring
(4) Adjusting Rod

(A) Foot Releasing Point
(B) Machine Stopping Point
L : Distance between Foot Releasing 

Point and the Machine Stopping 
Point

A : Length of Adjusting Rod From 

Stay

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands