manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 58

GENERAL

G23, G26, WSM

G-40

(EU)

Replacing Transmission Oil Filter

 CAUTION

To avoid personal injury :

• Allow engine to cool down sufficiently; oil can be hot and

can burn.

1. Remove the oil filter.
2. Put a film of clean transmission oil on rubber seal of new filter.
3. Tighten the filter quickly until it contacts the mounting surface.

Tighten filter by hand an additional 1/2 turn only.

4. After the new filter has been replaced, the transmission fluid

level will decrease a little. Make sure that the transmission fluid
does not leak through the seal, and check the fluid level.
Top off if necessary.

5. Properly dispose of used oil.

9Y1210294GEG0021US0

Adjusting Front Axle Pivot

If the front axle pivot pin adjustment is not correct, front wheel

vibration can occur causing vibration in the steering wheel.
1. Remove the split pin (2), tighten the adjusting nut (1)(tightening

torque 20 N·m, 2.0 kgf·m, 14.5 lbf·ft, then make sure that one of
the nut slots aligns with the split pin hole, tighten the nut slightly
clockwise if necessary to align. Replace the split pin (2).

9Y1210294GEG0044US0

(1) Transmission Oil Filter

(1) Adjusting Nut

(2) Split Pin

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands