manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 37

GENERAL

G23, G26, WSM

G-19

(EU)

Checking Transmission Fluid Level

1. Park the machine on a flat surface, raise the mower and lower

the grass catcher and shut off engine.

2. To check the oil level, draw out the dipstick (2), wipe it clean,

replace it, and draw it out again. Check to see that the oil level
lies between the two notches. If the level is too low, add new oil
to the prescribed level at the oil inlet (1). (Refer to
"LUBRICANTS, FUEL AND COOLANT" in this section.)

IMPORTANT

• If oil level is low, do not run the engine.

9Y1210294GEG0012US0

Checking Coolant Level

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

checking coolant level.

• Do not remove the radiator cap while coolant is hot. When

cool, slowly rotate cap to the first stop and allow sufficient
time for excess pressure to escape before removing the
cap completely.

1. Check to see that the coolant level is between the 

Highest level

and 

Lowest level

 marks of recovery tank (1).

2. When the coolant level drops due to evaporation, add water

only. In case of leakage, add anti-freeze and water in the
specified mixing ratio up to the 

Highest level

. 

(See page G-47.)

IMPORTANT

• If the radiator cap has to be removed, follow the caution

above and securely retighten the cap.

• Use clean, distilled water and anti-freeze to fill the radiator.

9Y1210294GEG0013US0

(2) Mower

1. Oil leak.
2. Make sure blade cap screws are tight.
3. Blade wear or damage.
4. Check all hardware.
5. Make sure all pins are in place.
6. Mower deck cleaning.

9Y1210294GEG0014US0

(3) While Sitting on the Operator's Seat

1. Speed control pedal and brake pedal.
2. Brake lock.

9Y1210294GEG0015US0

(4) Turning the Key Switch "ON"

1. Performance of the easy checker light.

9Y1210294GEG0016US0

(5) Starting the Engine

1. Color of the exhaust fumes.
2. Safety start switch, seat safety control and another safety devices.
3. Check for abnormal noise and vibration.

9Y1210294GEG0017US0

(1) Oil Inlet
(2) Dipstick

A : Oil level is acceptable within this 

range.

(1) Recovery Tank

A : Highest Level
B : Lowest Level

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands