manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 128

ENGINE

G23, G26, WSM

1-S46

(EU)

Correcting Valve and Valve Seat

NOTE

• Before correcting the valve and seat, check the valve stem

and the I.D. of valve guide section and repair them if
necessary.

• After correcting the valve seat, be sure to check the valve

recessing.

1) Correcting Valve

1. Correct the valve with a valve refacer.

[G23]

[G26]

2) Correcting Valve Seat

1. Slightly correct the seat surface with a 1.0 rad (60 °) (intake

valve) or 0.79 rad (45 °) (exhaust valve) valve seat cutter.

2. Resurface the seat surface with a 0.52 rad (30 °) valve seat

cutter to intake valve seat and with a 0.26 rad (15 °) valve seat
cutter to exhaust valve seat so that the width is close to
specified valve seat width (2.12 mm, 0.0835 in.).

3. After resurfacing the seat, inspect for even valve seating, apply

a thin film of compound between the valve face and valve seat,
and fit them with a valve lapping tool.

4. Check the valve seating with prussian blue. The valve seating

surface must show good contact all the way around.

[G23]

[G26]

9Y1210294ENS0056US0

Valve Lapping

1. Apply the compound evenly to the valve lapping surface.
2. Insert the valve into the valve guide. Lap the valve onto its seat

with a valve flapper or screwdriver.

3. After lapping the valve, wash the compound away and apply oil,

then repeat valve lapping with oil.

4. Apply prussian blue to the contact surface to check the seated

rate. If it is less than 70 %, repeat valve lapping again.

IMPORTANT

• When valve lapping is performed, be sure to check the

valve recessing and adjust the valve clearance after
assembling the valve.

9Y1210294ENS0057US0

Valve face angle

Factory specification

0.79 rad
45 °

Valve face angle

Factory 
specifica-
tion

IN.

1.0 rad
60 °

EX.

0.79 rad
45 °

Valve seat angle

Factory specification

0.79 rad
45 °

Valve seat angle

Factory 
specifica-
tion

IN.

1.0 rad
60 °

EX.

0.79 rad
45 °

(1) Valve Seat Width
(2) Identical Dimensions

(A) Check Contact
(B) Correct Seat Width
(C) Check Contact
(a) 0.26 rad (15 °) or 0.52 rad (30 °)
(b) 0.79 rad (45 °) or 1.0 rad (60 °)
(c) 0.52 rad (30 °) or 0.26 rad (15 °)

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands