manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 286

ELECTRICAL SYSTEM

G23, G26, WSM

6-S8

(EU)

Battery Specific Gravity

1. Check the specific gravity of the electrolyte in each cell with a

hydrometer.

2. When the electrolyte temperature differs from that at which the

hydrometer was calibrated, correct the specific gravity reading
following the formula mentioned in 

(Reference)

.

3. If the specific gravity is less than 1.215 (after it is corrected for

temperature), charge or replace the battery.

4. If the specific gravity differs between any two cells by more than

0.05, replace the battery.

NOTE

• Hold the hydrometer tube vertical without removing it from

the electrolyte.

• Do not suck too much electrolyte into the tube.
• Allow the float to move freely and hold the hydrometer at

eye level.

• The hydrometer reading must be taken at the highest

electrolyte level.

(Reference)

• Specific gravity slightly varies with temperature. To be exact,

the specific gravity decreases by 0.0007 with an increase of
1 °C (0.0004 with an increase of 1 °F) in temperature, and
increases by 0.0007 with a decreases of 1 °C (0.0004 with a
decrease of 1 °F).
Therefore, using 20 °C (68 °F) as a reference, the specific
gravity reading must be corrected by the following formula :
–

Specific gravity at 20 °C = Measured value + 0.0007 ×
(electrolyte temperature 

−

20 °C)

–

Specific gravity at 68 °F = Measured value + 0.0004 ×
(electrolyte temperature 

−

68 °F)

At an electrolyte temperature of 20 °C (68 °F)

WSM000001ELS0002US0

(2) Main Switch

Main Switch Connector Voltage

1. Remove the under cover panel.
2. Disconnect the 

4P

 connector (2) and remove the main switch

(1).

3. Measure the voltage with a voltmeter across the connector 

30

(red) terminal and chassis.

4. If the voltage differs from the battery voltage (11 to 14 V), the

wiring harness is faulty.

9Y1210294ELS0006US0

Specific Gravity

State of Charge

1.260 Sp. Gr.

100 % Charged

1.230 Sp. Gr.

75 % Charged

1.200 Sp. Gr.

50 % Charged

1.170 Sp. Gr.

25 % Charged

1.140 Sp. Gr.

Very Little Useful Capacity

1.110 Sp. Gr.

Discharged

(a) Good
(b) Bad

(c) Bad

Voltage

Connector 

30

 terminal – 

chassis

Approx. battery voltage

(1) Main Switch

(2)

4P

 Connector

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands