manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 38

GENERAL

G23, G26, WSM

G-20

(EU)

(6) Others

1. Check the areas where previous trouble was experienced.

9Y1210294GEG0018US0

[2] CHECK POINTS OF INITIAL 50 HOURS

Changing Engine Oil

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

changing the oil.

• Allow engine to cool down sufficiently; oil can be hot and

may cause burns.

1. To drain the used oil, remove the drain plug at the bottom of the

engine and drain the oil completely into the oil pan.
All the used oil can be drained out easily when the engine is still
warm.

2. After draining, reinstall the drain plug (3).
3. Fill with the new oil up to the upper notch on the dipstick (2).

(Refer to "LUBRICANTS, FUEL AND COOLANT" in this
section.)

4. Properly dispose of used oil.

9Y1210294GEG0019US0

Replacing Engine Oil Filter

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

changing the oil and the oil filter.

• Allow engine to cool down sufficiently; oil can be hot and

may cause burns.

1. Remove the oil filter.
2. Put a film of clean engine oil on the rubber seal of the new filter.
3. Tighten the filter quickly until contacts the mounting surface.

Tighten filter by hand an additional 1/2 turn only.

4. After new filter has been replaced, the engine oil normally

decreases a little. Make sure that the engine oil does not leak
through the seal and be sure to check the oil level on the
dipstick. Then, replenish the engine oil up to the prescribed
level.

5. Properly dispose of used oil.

IMPORTANT

• To prevent serious damage to the engine, use only a

KUBOTA genuine filter.

9Y1210294GEG0020US0

Oil capacity with filter

G23

3.1 L
3.3 U.S.qts
2.7 Imp.qts

G26

3.5 L
3.7 U.S.qts
3.1 Imp.qts

(1) Oil Inlet
(2) Dipstick
(3) Drain Plug
(4) Front Tyre (LH)

A : Oil lever is acceptable within this 

range.

(1) Engine Oil Filter

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands