manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 160

TRANSAXLE

G23, G26, WSM

2-M10

(EU)

(3) PTO Clutch "Disengaged"

When the PTO lever is set to 

"DISENGAGED"

 position, the pressurized hydraulic oil does not flow in to the PTO

clutch assembly.

The brake spring (7) pushes the clutch piston (6) to the PTO clutch case side.
The brake disks (10) and the brake plates (9) mounting on the PTO clutch case (8) are braked by its friction.
And the disk plates (4) and the separate plates (5) mounting on the spline boss (3), and the PTO clutch case (8)

are separated.

9Y1210294TXM0008US0

(1) Pulley
(2) Case
(3) Spline Boss
(4) Disk Plate

(5) Separate Plate
(6) Clutch Piston
(7) Brake Spring
(8) PTO Clutch Case

(9) Brake Plate
(10) Brake Disc

A : PTO Clutch "Disengaged"
B : PTO Clutch "Engaged"

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands