manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 132

ENGINE

G23, G26, WSM

1-S50

(EU)

(2) Timing Gears, Camshaft and Governor Gear

Timing Gear Backlash

1. Set a dial indicator (lever type) with its tip on the gear tooth.
2. Move the gear to measure the backlash, holding its mating gear.
3. If the backlash exceeds the allowable limit, check the oil

clearance of the shaft and the gear.

4. If the oil clearance is proper, replace the gear.

[G23]

[G26]

9Y1210294ENS0062US0

Governor Gear Backlash (G26)

9Y1210294ENS0063US0

Idle Gear 1 Side Clearance

1. Set a dial indicator with its tip on the idle gear.
2. Measure the side clearance by moving the idle gear to the front

and rear.

3. If the measurement exceeds the allowable limit, replace the idle

gear collar.

9Y1210294ENS0064US0

Backlash between idle 
gear and crank gear

Factory specification

0.0430 to 0.124 mm
0.00170 to 0.00488 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear and cam gear

Factory specification

0.0470 to 0.123 mm
0.00185 to 0.00484 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear and injection pump 
gear

Factory specification

0.0460 to 0.124 mm
0.00182 to 0.00488 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between oil 
pump drive gear and 
crank gear

Factory specification

0.0410 to 0.123 mm
0.00162 to 0.00484 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear 1 and crank gear

Factory specification

0.0320 to 0.115 mm
0.00126 to 0.00452 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear 1 and cam gear

Factory specification

0.0360 to 0.114 mm
0.00142 to 0.00448 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear 1 and injection 
pump gear

Factory specification

0.0340 to 0.116 mm
0.00134 to 0.00456 in.

Allowable limit

0.15 mm
0.0059 in.

[A] G23

[B] G26

Backlash between 
injection pump gear and 
governor gear

Factory specification

0.0300 to 0.117 mm
0.00119 to 0.00460 in.

Allowable limit

0.15 mm
0.0059 in.

Idle gear 1 side 
clearance

Factory specification

0.20 to 0.51 mm
0.0079 to 0.020 in.

Allowable limit

0.80 mm
0.031 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands