manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 285

ELECTRICAL SYSTEM

G23, G26, WSM

6-S7

(EU)

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

 CAUTION

• To avoid accidental short circuit, be sure to attach the positive cable to the positive terminal before the

negative cable is attached to the negative terminal.

• Never remove the battery cap while the engine is running.
• Keep electrolyte away from eyes, hands and clothes. If you are spattered with it, wash it away completely

with water immediately.

• Keep open sparks and flames away from the battery at all times. Hydrogen gas mixed with oxygen

becomes very explosive.

IMPORTANT

• If the machine is to be operated for a short time without battery (using a slave battery for starting), use

additional current (lights) while engine is running and insulate terminal of battery. If this advice is
disregarded, damage to alternator and regulator may result.

9Y1210278ELS0004US0

(1) Battery

Battery Voltage

1. Stop the engine and turn the main switch 

OFF

.

2. Connect the COM (

−

) lead of the voltmeter to the battery's

negative terminal post and the (+) lead to the positive terminal
post, and measure the battery voltage.

3. If the battery voltage is less than the factory specification, check

the battery specific gravity and recharge the battery.

9Y1210294ELS0004US0

Battery Terminal Connection

1. Turn the main switch 

ON

, and turn on the head light.

2. Measure the voltage with a voltmeter across the battery's

positive terminal post and the cable terminal, and the voltage
across the battery's negative terminal post and the chassis.

3. If the measurement exceeds the factory specification, clean the

battery terminal posts and cable clamps, and tighten them
firmly.

9Y1210294ELS0005US0

Battery voltage

Factory specification

More than 12 V

(1) Battery

Potential difference

Factory specification

Less than 0.1 V

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands