manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 130

ENGINE

G23, G26, WSM

1-S48

(EU)

Oil Clearance between Rocker Arm and Rocker Arm Shaft

1. Measure the rocker arm shaft O.D. with an outside micrometer.
2. Measure the rocker arm I.D. with an inside micrometer, and

then calculate the oil clearance.

3. If the oil clearance exceeds the allowable limit, replace the

rocker arm and measure the oil clearance again. If it still
exceeds the allowable limit, replace also the rocker arm shaft.

[G23]

[G26]

9Y1210294ENS0060US0

Push Rod Alignment

1. Place the push rod on V blocks.
2. Measure the push rod alignment.
3. If the measurement exceeds the allowable limit, replace the

push rod.

9Y1210272ENS0068US0

Oil clearance between 
rocker arm and rocker 
arm shaft

Factory specification

0.016 to 0.045 mm
0.00063 to 0.0017 in.

Allowable limit

0.15 mm
0.0059 in.

Rocker arm shaft O.D.

Factory specification

10.473 to 10.484 mm
0.41233 to 0.41275 in.

Rocker arm I.D.

Factory specification

10.500 to 10.518 mm
0.41339 to 0.41409 in.

Oil clearance between 
rocker arm and rocker 
arm shaft

Factory specification

0.016 to 0.045 mm
0.00063 to 0.0017 in.

Allowable limit

0.10 mm
0.0039 in.

Rocker arm shaft O.D.

Factory specification

11.973 to 11.984 mm
0.47138 to 0.47181 in.

Rocker arm I.D.

Factory specification

12.000 to 12.018 mm
0.47244 to 0.47314 in.

Push rod alignment

Allowable limit

0.25 mm
0.0098 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands