manualshive.com logo in svg

Intel IXP45X, Developer'S Manual

Share
Download
Intel IXP45X Developer'S Manual Download Page 833

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Order Number: 306262-004US

833

Time Synchronization Hardware Assist (TSYNC)—Intel

®

 IXP45X and Intel

®

 IXP46X Product 

Line of Network Processors

19.3.4

Delay_Req Message

Firmware in a time slave can transmit a Delay_Req message to the master for the 

purpose of determining propagation delays in the network. A Delay_Req message is 

defined as a value of 0x01 in byte 74 of the Ethernet frame after the start of frame 

delimiter.

The TSync logic will monitor the MII signals, detect when the channel has transmitted 

or received a Delay_Req message, and lock the timestamp. Furthermore, the TSync 

logic captures the Sequence ID and Source UUID if a Sync message is received by a 

channel configured as a time master.

19.3.5

Delay_Resp Message

Upon receipt of a Delay_Req message, firmware in a time master will transmit a 

Delay_Resp message that includes the timestamp of the Delay_Req message it 

received. No time stamping is done with the Delay_Resp message itself. A Delay_Resp 

message is defined with a value of 0x03 in byte 74 of the Ethernet frame after the start 

of frame delimiter.

The 1588 standard uses UDP/IP protocol, which implies that messages can be lost. 

Because a Delay_Req message can be locked out until firmware in the master channel 

enables it, the slave channel firmware will have to retry sending the Delay_Req 

message to the master if the slave does not receive a Delay_Resp message within 

some timeout period.

19.3.6

IPv6 Compatibility

A time sync message is always defined using an IPv4 message format. To avoid the 

potential of mistaking an IPv6 packet with a time sync packet, the byte at offset 14 will 

be checked for a value of 0x45. If not 0x45, the packet will be ignored. IPv6 is not 

supported

19.3.7

Traffic Analyzer Support

In a traffic analyzer type application, it is often desirable to timestamp every message 

on the network. An optional mode inhibits the “locking” of the time snapshot so that 

the SFD of every message triggers a time snapshot. In this mode the snapshot must be 

read (presumably by the NPE) during the message before the next SFD is received. 

19.3.8

MII Clocking Methods

According to the IEEE 802.3 specification, the MII TX/RX data transitions synchronously 

with the MII clock (rising edge is implied). For the TX case, txclk is driven by the PHY, 

but txdata is driven by MAC. The txdata bus transitions some time after rising edge of 

txclk and is sampled at next rising edge by the PHY. For the RX case, the PHY drives 

rxclk and rxdata. The rxdata bus transitions on the falling edge of rxclk to provide 

sufficient setup time for the MAC to sample at next rising edge. The characteristics of 

the MII in cases of transmit and receive should be taken into consideration when 

constraining the design for synthesis.

19.3.9

System Time Clock Rate Set by Addend Register

The FreqOscillator is the frequency of all portions of the frequency compensated clock, 

or time synchronization circuit. The frequency compensation value 

(FreqCompensationValue) is the number held in the Addend register, which is added to 

the accumulator once every 1/FreqOscillator. To determine the value that should be 

placed in the Addend register, the following equation is used:

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands