manualshive.com logo in svg

Intel IXP45X, Developer'S Manual

Share
Download
Intel IXP45X Developer'S Manual Download Page 317

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Order Number: 306262--, Revision: 004US

317

USB 1.1 Device Controller—Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network 

Processors

8.5.13

UDC Endpoint 11 Control/Status Register

(UDCCS11)

The UDC Endpoint 11 Control Status Register contains six bits that are used to operate 

Endpoint 11, a Bulk IN endpoint.

8.5.13.1

Transmit FIFO Service (TFS)

The transmit FIFO service bit is active if one or fewer data packets remain in the 

transmit FIFO. TFS is cleared when two complete packets of data remain in the FIFO. A 

complete packet of data is signified by loading 64 bytes of data or by setting 

UDCCS11[TSP].

8.5.13.2

Transmit Packet Complete (TPC)

The transmit packet complete bit is set by the UDC when an entire packet is sent to the 

host. When this bit is set, the IR11 bit in the appropriate UDC status/interrupt register 

is set if transmit interrupts are enabled.

This bit can be used to validate the other status/error bits in the Endpoint 11 Control/

Status Register. The UDCCS11[TPC] bit is cleared by writing a 1 to it. This clears the 

interrupt source for the IR11 bit in the appropriate UDC status/interrupt register, but 

the IR11 bit must also be cleared.

Setting this bit does not prevent the UDC from transmitting the next buffer. The UDC 

issues NAK handshakes to all IN tokens if this bit is set and neither buffer has been 

triggered by writing 64 bytes or setting UDCCS11[TSP].

Register

UDCCS10

Bits

Name

Description

31:8

Reserved for future use.

7

TSP

Transmit short packet (read/write 1 to set).
1 = Short packet ready for transmission.

6

(Reserved). Always reads 0.

5

FST

Force STALL (read/write).
1 = Issue STALL handshakes to IN tokens.

4

SST

Sent STALL (read/write 1 to clear).
1 = STALL handshake was sent.

3

TUR

Transmit FIFO underrun (read/write 1 to clear).
1 = Transmit FIFO experienced an underrun. 

2

FTF

Flush Tx FIFO (always read 0/ write a 1 to set).
1 = Flush Contents of TX FIFO.

1

TPC

Transmit packet complete (read/write 1 to clear).
0 = Error/status bits invalid.
1 = Transmit packet has been sent and error/status bits are valid.

0

TFS

Transmit FIFO service (read-only).
0 = Transmit FIFO has no room for new data.
1 = Transmit FIFO has room for 1 complete data packet.

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands