Intel IXP45X Developer'S Manual Download Page 745

Page: 745 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

August 2006

Developer’s Manual

Reference Number: 306262-004US

745

HSS Coprocessor—Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Figure 180

, the ‘a’ denotes the first E1 stream, the ‘b’ denotes the second E1

stream, the two streams are interlaced byte wise. Another method of placing E1 stream

on this backplane is to process the first entire E1 stream followed by the second

complete E2 stream (frame interleaving).

Figure 181

illustrates a method in which two T1 frames are placed on a 4.096-Mbps

backplane. It can be seen that the first two timeslots are unassigned with the exception

of the frame pulse. The first three timeslots of each T1 stream are then placed

(interlaced) in succession on the bus, then one unassigned timeslot per T1 stream

present are placed on the bus. Unassigned RX bytes do not pass through the HSS FIFO

(lookup tables give unassigned timeslots).

The HSS can also transmit unassigned timeslots, the value of which is programmable.

The NPE Core need only supply the contents of the T1 frames, it does not need to

transmit unused timeslots to the HSS. The location of these unassigned timeslots are

defined by the lookup table.

The backplane can contain the 2 T1 streams byte interlaced as shown in

Figure 181

the T1 stream can be placed in its entirety first followed by eight unassigned timeslots

(frame pulse at the last bit of the 32

timeslot. The second T1 stream then

commences followed by eight unassigned timeslots. The frame pulse is coincidental

with the last bit in the 32

timeslot. The second timeslot follows the format of the first

timeslot and together take up the 64 timeslots available. Once again the HSS can be

programmed by the NPE Core to ignore the eight unassigned timeslots while taking the

frame bit into account.

Figure 180. MVIP, Byte Interlacing Two E1 Streams onto a 4.096-Mbps Backplane

10a 10b 11a 11b 12a 12b 13a 13b 14a 14b 15a 15b

Timeslots

Bits

31b

16a

4. 096

MHz clock

Frame pulse

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands

Intel IXP45X, Developer'S Manual

Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands