manualshive.com logo in svg

Intel IXP45X, Developer'S Manual

Share
Download
Intel IXP45X Developer'S Manual Download Page 706

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors—Expansion Bus

Controller

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

706

Order Number: 306262-004US

The EXP_TIMING_CS registers may only be written if there is not an outstanding 

Expansion bus transaction. Software must ensure that all outstanding Expansion bus 

transfers are complete before changing the EXP_TIMING_CS registers.

12.5.9

Configuration Register 0 

At power up or whenever RESET_IN_N is asserted, the expansion bus address outputs 

are switched to inputs and the states of the bits are captured and stored in 

Configuration Register 0, bits 23 through 0. This occurs when PLL_LOCK is deasserted.   

15:14

CYC_TYPE

00 = Configures the Expansion bus for Intel cycles.
01 = Configures the Expansion bus for Motorola cycles.
10 = Configures the Expansion bus for HPI cycles.
        (HPI reserved for chip selects [7:4] only)
11 = Configures the Expansion bus for Micron ZBT cycles

13:9

CNFG[4:0]

Device Configuration Size. Calculated using the formula:
     SIZE OF ADDR SPACE = 2

(9+CNFG[4:1]+16*CNFG[0])

For Example:
00000 = Address space of 2

9 

= 512 Bytes

00010 = Address space of 2

10 

= 1024 Bytes

   …
10000 = Address space of 2

17

 = 128 Kbytes

   …
11100 = Address space of 2

23

 = 8 Mbytes

11110 = Address space of 2

24

 = 16 Mbytes

00001 = Address space of 2

25

 = 32Mbytes

8

Sync_Intel

Synchronous Intel StrataFlash

®

 select. This bit must be 0 if 

CYC_TYPE is not programmed to Intel cycles.
0 = Target device is not a Synchronous Intel StrataFlash
1 = Target device is a Synchronous Intel StrataFlash

7

EXP_CHIP

0 = Target device is not one of the IXP45X/IXP46X network 

processors
1 = Target device is one of the IXP45X/IXP46X network 

processors. This bit must only be set to 1 when CYC_TYPE is 

configured to be Intel Cycles and Sync_Intel is set to 0.

6

BYTE_RD16

Byte read access to Half Word device
0 = Byte access disabled.
1 = Byte access enabled.

5

HRDY_POL

HPI HRDY polarity (reserved for EX_CS_N[7:4] only)
0 = Polarity low true.
1 = Polarity high true.

4

MUX_EN

0 = Separate address and data buses.
1 = Multiplexed address / data on data bus.

3

SPLT_EN

0 = AHB split transfers disabled.
1 = AHB split transfers enabled.

2

WORD_EN

1 = Expansion bus uses 32-bit data bus
0 = Expansion bus uses 8/16 bit data bus based on BYTE_EN bit

1

WR_EN

0 = Writes to CS region are disabled.
1 = Writes to CS region are enabled.

0

BYTE_EN

0 = Expansion bus uses 16-bit-wide data bus if WORD_EN = 0.
1 = Expansion bus uses only 8-bit data bus if WORD_EN = 0.

Table 228.

Bit Level Definition for each of the Timing and Control Registers (Sheet 2 of 2)

Bits

Name

Description 

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands