manualshive.com logo in svg

Intel IXP45X, Developer'S Manual

Share
Download
Intel IXP45X Developer'S Manual Download Page 258

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors—Ethernet MACs

Intel

®

 IXP45X and Intel

®

 IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

258

Order Number: 306262-004US

• Address Mask[23:16] — Address Mask 4
• Address Mask[15:8] — Address Mask 5
• Address Mask[7:0] — Address Mask 6

Example: Address Mask is 00-A0-24-D1-7F-02

• Address Mask 1 = 0x00
• Address Mask 2 = 0x00
• Address Mask 3 = 0x00
• Address Mask 4 = 0xFF
• Address Mask 5 = 0xFF
• Address Mask 6 = 0x00

The detailed bit descriptions follow the six registers’ bit maps.

6.2.31

Address Mask 1

6.2.32

Address Mask 2

Register Name:

addrmask1

Hex Offset Address:

0x C80090A0

Reset Hex Value:

0x00000000

Register

Description:

Address Mask Register #1. First register of six that makes up the Address Mask. Address 

Mask is used with Address for multicast address filtering. Bits set to 1 in Address Mask 

represent bits of the Address Register that must match the corresponding bits in incoming 

destination addresses for packets to be accepted

Access: Read/Write.

31

8

7

0

(Reserved)

ADDRESS MASK[7:0]

Register Name:

addrmask2

Hex Offset Address:

0x C80090A4

Reset Hex Value:

0x00000000

Register

Description:

Address Mask Register #1. Second register of six that makes up the Address Mask. Address 

Mask is used with Address for multicast address filtering. Bits set to 1, in Address Mask, 

represent bits of the Address Register that must match the corresponding bits in incoming 

destination addresses for packets to be accepted.

Access: Read/Write.

31

8

7

0

(Reserved)

ADDRESS MASK[15:8]

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands