Intel IXP45X Developer'S Manual Download Page 438

Page: 438 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors—USB 2.0 Host Controller

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

438

Order Number: 306262-004US

An AsyncSchedSleepTime value of 10

s provides a reasonable relaxation of the system

memory load and still provides a good level of service for the various transfer types and

payload sizes. For example, say we detect an empty list after issuing a start-split for a

64-byte full-speed bulk request. Assuming this is the only thing in the list, the host

controller will get the results of the full-speed transaction from the hub during the fifth

complete-split request. If the full-speed transaction was an IN and it nak'd, the 10

sleep period would allow the host controller to get the NAK results on the first

complete-split.

9.14.8.5

Asynchronous Schedule Traversal: Start Event

Once the HC has idled itself via the empty schedule detection (

Section 9.14.8.3,

“Empty Asynchronous Schedule Detection” on page 435

), it will naturally activate and

begin processing from the Periodic Schedule at the beginning of each micro-frame. In

addition, it may have idled itself early in a micro-frame. When this occurs (idles early in

the micro-frame) the HC must occasionally re-activate during the micro-frame and

traverse the asynchronous schedule to determine whether any progress can be made.

The requirements and method for this restart are described in

Section 9.14.8.4,

“Restarting Asynchronous Schedule Before EOF” on page 435

. Asynchronous schedule

Start Events are defined to be:

• Whenever the host controller transitions from the periodic schedule to the

asynchronous schedule. If the periodic schedule is disabled and the asynchronous

schedule is enabled, then the beginning of the micro-frame is equivalent to the

transition from the periodic schedule, or

• The asynchronous schedule traversal restarts from a sleeping state (see

Section

9.14.8.4, “Restarting Asynchronous Schedule Before EOF” on page 435

9.14.8.6

Reclamation Status Bit (USBSTS Register)

The operation of the empty asynchronous schedule detection feature (

Section 9.14.8.3,

“Empty Asynchronous Schedule Detection” on page 435

) depends on the proper

management of the Reclamation bit in the USBSTS register. The host controller tests

for an empty schedule just after it fetches a new queue head while traversing the

asynchronous schedule (See

Section 9.14.10.1, “Fetch Queue Head” on page 443

It is required that the host controller sets the Reclamation bit to a one whenever an

asynchronous schedule traversal Start Event, as documented in

“Asynchronous

Schedule Traversal: Start Event” on page 438

, occurs. The Reclamation bit is also set

to a one whenever the host controller executes a transaction while traversing the

asynchronous schedule (see

Section 9.14.10.3, “Execute Transaction” on page 444

The host controller sets the Reclamation bit to a zero whenever it finds a queue head

with its H-bit set to a one. Software should only set a queue head's H-bit if the queue

head is in the asynchronous schedule. If software sets the H-bit in an interrupt queue

head to a one, the resulting behavior is undefined. The host controller may set the

Reclamation bit to a zero when executing from the periodic schedule.

Speed

~12 µs

Approximate typical for 8-byte bulk/control (i.e. setup)

Size 8

Type Cntrl

Table 174.

Typical Low- /Full-Speed Transaction Times (Sheet 2 of 2)

Transaction Attributes

Footprint

(Time)

Description

Summary of Contents for IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands

Intel IXP45X, Developer'S Manual

Search results

Summary of Contents for IXP45X

Reviews:

Brands by name

Popular brands