Fiat Punto 2004 Training Manual Download Page 398

Page: 398 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Use control module

The Nuova Punto “Famiglia1” architecture provides for integration of the user controls within

switch holder modules.

The modules are listed in the table below, together with the other controls.

Modules

Origin

CDC,RDC

(Passenger’s rear/front door window regulator control)

New

Stop switch

Common component derived from

Opel

CSM

(Steering column stalk control module)

Derived from Ypsilon

Switch on the clutch

Common component derived from

Opel

Control dashboard on the driver’s side front door

New

CSS

(Central control dashboard)

New

ELC

(Left control dashboard)

New

Steering wheel controls for the horn and the audio/telephone systems

New

Information-communication/roof control dashboard on the ceiling light

fixture

New

Gearshift control lever

The derived components feature the same interface to the vehicle wiring (wiring

diagram/connector) as the reference model.

gb Fiat Grande Punto OK

397 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands