Fiat Punto 2004 Training Manual Download Page 165

Page: 165 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.11 Sensors

Revs sensor

It is fitted onto the engine base and “faces” towards the phonic wheel positioned on the engine

flywheel.

It is of the induction type, i.e. it operates through the variation of the magnetic field generated

by the passage of the phonic wheel teeth (60 – 2 teeth).

The injection control unit uses the revs sensor signal to:

determine the engine rotation speed;

determine the angular position of the drive shaft.

gb Fiat Grande Punto OK

165 / 532

The figure illustrates the revs sensor components.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands