Fiat Punto 2004 Training Manual Download Page 474

Page: 474 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

The window regulating function can be actuated on both sides (right & left) only when the key

is inserted.

Following the key-OFF, the front windows can only be actuated manually over a period of 3

minutes. After this time has elapsed, the system will not be acquiring new commands any

more.

gb Fiat Grande Punto OK

473 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 474 / 533

Search results

Summary of Contents for Punto 2004

Reviews: