Fiat Punto 2004 Training Manual Download Page 88

Page: 88 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

E.G.R. solenoid valve

The purpose of the Pierburg E.G.R. solenoid valve (fitted to the cylinder head) is to modulate

the exhaust gas flow to the intake, depending on the control of the injection control unit.

Modulation takes place by means of the inner solenoid (PWM-controlled by the control unit),

which actuates the control rod of the inner valve that conveys, after it has opened, the gas into

the inlet manifold.

E.G.R. valve body

Gas inlet from the exhaust manifold

Gas outlet to the inlet manifold

Solenoid positive

FIAT PUNTO

88 / 532

Solenoid negative

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands