Fiat Punto 2004 Training Manual Download Page 443

Page: 443 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Manual rear window wiper operation mode:

by turning the ring of the steering column stalk

rear window wiper lever, located on the driver’s right, to ON, the windscreen wiper will be

actuated as described below:

intermittent operation: a pause of 2.7 seconds between two subsequent strokes;

interlocking to the windscreen wiper (in case of simultaneous request): synchronous operation

at a frequency equal to half the windscreen wiper.

continuous operation: with the reverse gear engaged.

Smart rear washing:

by moving the steering column stalk right-hand lever, rear washing will

be actuated. By keeping the lever pushed for more than 0.5 seconds, the rear window wiper

will be automatically actuated at continuous speed. When the control is released, the washing

will be turned off and three further rear window wiping strokes will occur, followed by one

further wiping every 6 seconds to remove dripping.

gb Fiat Grande Punto OK

442 / 532

In the event that the rear window wiper has already been actuated prior to actuating the

washing control through the lever, the smart washing logic will only be performed to actuate

the same in the intermittent mode.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 443 / 533

Search results

Summary of Contents for Punto 2004

Reviews: