Fiat Punto 2004 Training Manual Download Page 62

Page: 62 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

The engines feature the performance levels below:

max. rating: 55 kW (75 HP) EC at 4,000 r.p.m.; 66 kW (90 HP) EC at 4,000 r.p.m.

max. torque: 190 Nm (19.4 kgm) EC at 1,750 r.p.m.; 200 Nm (20.4 kgm) at 1,750 r.p.m.

To reduce polluting emissions, these engines are equipped with:

- exhaust system with oxidizing catalytic converter;

- exhaust gas recirculation (E.G.R.) system (modified for the 90 HP version) with heat

exchanger;

- engine base vapour/gas recirculation system;

- UEGO oxygen sensor (temperature sensors for DPF available as options for 90 HP versions

only);

- new DRV 2 pressure regulator;

- new RDS 4 air pressure sensor.

The unit consists of a system made up of the engine and all the systems required for its

operation:

- fuel feed system;

- air boosting system;

- engine cooling system;

- exhaust system with catalytic converter;

- oil vapour recirculation system;

- exhaust gas recirculation (E.G.R.) system with heat exchanger;

FIAT PUNTO

62 / 532

The operation of these systems can be optimized by means of an electronic control system

managed by a control unit.

Understanding the control unit operation logic allows you to get an overall picture of the entire

system.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 62 / 533

Search results

Summary of Contents for Punto 2004

Reviews: