Fiat Punto 2004 Training Manual Download Page 508

Page: 508 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

node will exhibit the same behaviour as

the preceding step. Key-controlled

power supply (+15).

Cut-off with run-

down battery

Signal (CrashOutputSts) available

The function is ensured by an internal

power reserve for a maximum time of

150 msec.

In case of collision, the SDM will transmit, through the B-CAN line, a proper collision signal

(STATUS SDM.CrashOutputSts): this signal will inform the network about the type of collision

and the time when it occurred.

The airbag node will perform its functions, as shown in the table below:

Functions Driver’s

side

airbag

Passen

ger’s

side

airbag

Front

airbag

Internal

accelerom.

Internal

accelerom.

Safety

function

Actuation

threshold

Front

protection

Pretensioner

Side

protection

X X

Side

limiter

Rear

protection

TBD

Fuel

cut-off

gb Fiat Grande Punto OK

507 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands