Fiat Punto 2004 Training Manual Download Page 509

Page: 509 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Recovery

R1 = Accelerometer signal X: actuation not ensured.

Accelerometer signal Y: front airbags and pretensioners enabled; side and head airbags

disabled.

Power reserve: actuation not ensured.

ASIC: actuation ensured

Microprocessor: actuation disabled.

Memory: actuation disabled (ECU reset).

Sensor safing: front airbag and pretensioner disabled, side and head airbags ensured.

R2 = unsafe actuation due to faults.

R3 = in case of collision, the control unit will try actuation.

R4 = passenger’s front airbag disable and passenger’s airbag warning light lighting.

R5 = actuation ensured.

R6 = actuation disabled by the control unit.

R7 = the CAN communication will stop for 1 second. The passenger’s airbag will be switched

off during this time.

R9 = actuation available. It may be cleared off the event memory when all of the following

conditions apply:

R8 = relative to side and head airbag disable. The opposed side and head airbags will be

ensured. The front airbags and pretensioners will be ensured.

· one airbag and pretensioner is not actuated;

· pretensioner actuation other than the third one;

· side airbag actuation other than the third one.

R10 = front and passenger’s airbag disabled, and passenger’s airbag warning light ON.

gb Fiat Grande Punto OK

508 / 532

R11 = if the passenger’s airbag deactivation warning light status or switch are not clear (either

of them is faulty, or out-of-time message), the warning light will be actuated immediately and

the passenger’s airbag will be promptly deactivated.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands