Fiat Punto 2004 Training Manual Download Page 132

Page: 132 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Low engine oil pressure sensor signal

Air flow meter air temperature signal

Not connected

Air flow meter air flow rate signal

E.G.R. solenoid valve negative

Cylinder 1 injector negative

Cylinder 2 injector positive

Not connected

Phase sensor negative

Not connected

Sucked air temperature and boosting pressure sensor positive

Sucked air temperature and boosting sensor negative

Phase sensor positive

Not connected

Air flow meter negative

Not connected

Engine coolant temperature sensor ground

Not connected

Cylinder 3 injector negative

Not connected

Fuel pressure regulator negative

Not connected

FIAT PUNTO

132 / 532

Not connected

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 132 / 533

Search results

Summary of Contents for Punto 2004

Reviews: