Fiat Punto 2004 Training Manual Download Page 417

Page: 417 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

When the maximum kilometre distance that can be displayed on the trip odometer is reached,

the latter will display 0.0 again.

Example (Mode panel)

Trip Computer items:

Fuel distance

[km] or [miles]: it indicates the estimated distance hat can be covered with the

fuel found in the tank, by assuming that the driver will keep on driving by following the same

driving behaviour.

Covered distance

[km] o [miles]: it indicates (0 to 9999.9 for the Comfort and Matrix panels, 0

to 3999.9 for the Mode panel) the distance covered by the vehicle from the start of the

mission, i.e. since the trip odometer has been reset by the driver. The indication is consistent

with the value shown on the odometer. The display is updated every 100 metres.

Average consumption

[k.p.l.] or [l/100 km] or [m.p.g.]: it indicates the average consumption

from the start of the mission. The unit of measurement [k.p.l.] cannot be selected in the Mode

panel.

Instant consumption

[k.p.l.] or [l/100 km] or [m.p.g.]: it indicates the fuel consumption

constantly updated. It helps the driver be aware of the consumption differences according to

the driving behaviour. The unit of measurement [k.p.l.] cannot be selected in the Mode panel.

Average speed

[k.p.h.] or [m.p.h.]: it is calculated starting from the start of the missions.

gb Fiat Grande Punto OK

416 / 532

Driving time

[hh:mm]: it indicates the time [00:00 to 99:59) elapsed since the start of the

mission, with resolution and updating of 1 minute. When the maximum value is reached, the

count will be reset automatically.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 417 / 533

Search results

Summary of Contents for Punto 2004

Reviews: