Fiat Punto 2004 Training Manual Download Page 455

Page: 455 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

9.2.10 Rain sensor control unit (RLS)

The rain sensor control unit (RLS) is an electronic component connected to the Body

Computer node (BCM) through a LIN serial line. It manages, together with a control located on

the steering column stalk module (CSM), the windscreen wiper stroke speed setting function.

The rain sensor control unit is connected through a special bridle located on the internal rear-

view mirror, which is connected to the front body wiring harness. It is made up of a infrared

LED sensor fitted to the vehicle’s front window and is capable of detecting the presence of rain

and, as a result, managing the wiping operation depending on the amount of water found on

the glass.

9.2.11 Brake pedal switch

gb Fiat Grande Punto OK

454 / 532

This switch is located on the brake pedal and is connected to the body-to-front cable harness.

Its function is to indicate the brake pedal status in order to report the latter to the control units

that request so.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands