Fiat Punto 2004 Training Manual Download Page 512

Page: 512 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Signalling warning light.

Class A errors: any error that represents a risk of incorrect minimum actuation of the airbag

squibs. With this type of error, the warning light will remain ON, even when the error is

intermittent and has been solved, until the ECU is reset.

Class B errors: any error that does not represent a risk of incorrect actuation of the airbag

squibs. With this type of error, the warning light will remain ON for 30 seconds and then will go

out.

9.8 Fire protection

In the late 1990s, the introduction of the new European regulations on the crash tests and also

of the injection fuel feed system has made FIAT AUTO aware of the need to define from the

start the bodywork construction design principles and the layout of the various systems fitted

to motorcars.

For this reason, the whole of Fiat Punto, from the body to every single component, has been

designed so as to comply with the strictest, latest FIAT in-house fire prevention regulations.

Fire Prevention System (FPS).

All the petrol and diesel engine versions feature the FPS (Fire Prevention System) inertia

switch, which causes the engine to be switched off immediately a few milliseconds after a

collision.

The plastic tank, conforming to the forthcoming directives, is located in an area protected in

case of collision. It can withstand distortion (if any) with no risk of fuel escape; moreover, it

poses no explosion hazard if the vehicle is set on fire, due to its being made of plastic.

gb Fiat Grande Punto OK

511 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 512 / 533

Search results

Summary of Contents for Punto 2004

Reviews: