Fiat Punto 2004 Training Manual Download Page 458

Page: 458 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Electric window regulator control on the rear doors (RDC)

The control on the rear door (left side and right side) (RDC) is connected through the cable

harness on the rear door. It is acquired by an electronic module located inside the window

regulator motor on the rear door, with automatic functioning both during the up and down

movement and anti-pinch protection.

The control receives the power supply for ideograph lighting and correct operation of the

control itself from the disable control placed on the control board on the driver’s side front

door.

9.2.13 Switch on clutch pedal

The clutch pedal signalling switch is fitted to the clutch pedal and is connected through the

body-to-front cable harness. It informs the engine management control unit about the pedal

status.

9.2.14 Central control board (CSS)

The central control board (CSS) includes the following buttons:

gb Fiat Grande Punto OK

457 / 532

“City” button for actuation/deactivation of the City mode on the electric drive;

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 458 / 533

Search results

Summary of Contents for Punto 2004

Reviews: