Fiat Punto 2004 Training Manual Download Page 279

Page: 279 / 533

8-VALVE 1.4

ENGINE

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

4.5 Operation logic

4.5.1 System self-adaptation

The control unit features self-adaptive functions that recognize the changes occurring in the

engine following time-adjustment processes and component or engine ageing.

These changes are stored into the memory as basic mapping modifications: their purpose is to

adapt the system operation to the progressive engine and component alterations compared

with as-new features.

This self-adapting feature also makes it possible to compensate for the unavoidable

differences (due to production tolerances) of replaced components (if any).

The control unit modifies, through the exhaust gas analysis, the basic mapping with respect to

the as-new features of the engine.

gb Fiat Grande Punto OK

279 / 532

The self-adaptive parameters will not be cleared when the battery is disconnected.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 279 / 533

Search results

Summary of Contents for Punto 2004

Reviews: